joiner's works joiner's works - main joiner's works - the main page joiner's business - main joiner's works - the main page of a site joiner's works
to joiner's works - the main page to the beginning joiner - main

Tools

To already available tools, it is necessary to add new tools, adaptations, materials. First of all, it is required an axe the average size (more hard tourist), luchkovaja a saw with a cloth for longitudinal pilenija. It is necessary level . It is wooden or metal kolodka in which the glass tubule filled with a nonfreezing liquid is built in. The air vial floating in a capsule shows a deviation of a plane from a horizontal. This inexpensive tool is better for getting in shop. But it is possible to take advantage of the self-made: fill in in a bottle from light glass water, having left a place for an air vial in length 15 - 20 mm, and it is dense zakuporte. The horizontal will be correct if air vial appears precisely in the middle of a bottle put sideways. .

It is possible to check up and reliability of the tool. Notice position of an air vial and turn a bottle a neck in the opposite direction: the vial should take the same place under glass. For self-made level the flat glass flask is more suitable.

It is useful a plumb . girka, suspended on a cord or a thick thread in length to 3м, it it is possible to reel up it on the coil. In quality girki it is possible to use a piece of any metal it is powerful 200 - 300г, pointed with the bottom end and having an aperture from above for cord fastening. Such cone is easy for melting from lead. Too easy cargo will deviate a wind. A plumb check vertical position of support and racks.

Will be useful on a summer residence and in a garden easy lomik , gvozdodyor , alligator wrenches for waterpipe repair, the electroreplacement tool . Will be useful scissors on gland when it is required to cut and correct strips of iron for roof repair, for manufacturing of trenches and drainpipes. .

Umeltsu it is necessary to deal with cement and a brick often enough. However development of new specialities does not represent great difficulties: to lay out a concrete path is easier, rather than for the first time to make a stool. About every second the gardener-fan carries out itself all joiner's and plotnichnye works, up to building of a garden small house, not to mention a shed. Rather seldom who from gardeners resorts to services of masons or concreters-professionals.

Short acquaintance to knitting materials (cement, izvest, plaster, clay) and napolniteljami (rubble, slag, gravel, sand, a brick), ways of their mixture and application is quite enough, that most to lay out structure base, oven of a simple design, to make plates for a decorative path to construct a reservoir, a cellar, etc.

Adaptations and the tool for concrete and brick works are not numerous and simple: a box for preparation of mixes, a hammer-pick, a roar for sifting napolnitelej, a wooden board with the handle, named the falcon, and masterok or kelma. Everything, except masterka, kelmy and a hammer, it is possible to make most for other listed adaptations on sale do not happen. .

Rastvornyj (tray) knock together a box from boards in width to 150 mm. The tray should be such size that in it it was possible to prepare so much solution, how many it is required on 2 business hours for the cement mortal quickly hardens, and to dilute with its water it is not recommended. The sizes of a tray can be such: length of 800 1000 mm, width 600 - 800 mm. A bottom do of iron or plywood sheet. A plywood bottom strengthen outside two-three laths. The rastvornyj box painted outside of an oil paint, can serve some years. For preparation of mixes the old trough, the big basin or other capacity with low boards and a smooth bottom is suitable.

the Roar for sifting of substances-napolnitelej represents the box which has been brought down from boards in width to 80 mm, same approximately the sizes, as well as rastvornyj a box, but with a bottom from a metal grid. The sizes of cells can fluctuate from 2 to 10 mm in dependence because that it is necessary to sift. .

Masterok and kelma are steel plates of the triangular form with the direct or bent handle. They are applied to drawing of a cement or limy solution in the course of a bricklaying or plaster works. There is enough and one of these tools.

the Hammer-pick , nasazhennyj on the wooden handle, on the one hand has a square core section 25x25 mm, and with another - the flat pointed blade in width to 50 mm. The tool is applied in a bricklaying for obkalyvanija a brick, giving to it of the necessary form. However for these purposes the ordinary metalwork hammer or strong enough kelma which edge it is possible to cut away a brick is quite suitable. .

the Falcon is a small wooden board with a short round core from the bottom party for which it hold the left hand in horizontal position during plaster works. For a board the square piece of thick plywood in the size 400X400 mm is suitable. The solution put on it take in the small portions and throw (sweep together) on a wall, then level masterkom or kelmoj, and then smooth (rub clean) a rather narrow wooden plate with the handle.

the Workplace. So, all new necessary tools and adaptations are. It is possible to undertake the workbench device. In any garden, usually in northern or western part of a site, there is a place called by an economic court yard. Here the small shed or a canopy, a warehouse of materials (sand, wood, peat, fertilizers), sadovohozjajstvennyj stock, a cellar, a shower, etc. are located. Here a place and to a workbench - not such graceful, as in a city, but to stronger and bolshemu on the size. On a bad weather case it is good to have a desktop in a shed, but it is possible to manage and an easy canopy over a workbench.